http://robin.me/pi robin.me pi Homepage

Tasmota


https://github.com/arendst/Tasmota/ Tasmota Homepage

https://thehackbox.org/tasmota/release/ Tasmota Binaries

https://templates.blakadder.com/howto.html Tasmota Templates

https://resource.heltec.cn/download/WiFi_Kit_8/WIFI_Kit_8_Pinout_Diagram(new).pdf Heltec wifi 8 pinout
Heltecbackup.dmp

http://robin.me/Heltecbackup.dmp Heltec backup settings

https://github.com/thehookup/Wireless_MQTT_Doorbell/blob/master/GPIO_Limitations_ESP8266_NodeMCU.jpg?raw=true Best gpio pins for 8266

https://github.com/thehookup/ESP32_Ceiling_Light/blob/master/GPIO_Limitations_ESP32_NodeMCU.jpg?raw=true Best gpio pins for esp32

https://randomnerdtutorials.com/esp8266-pinout-reference-gpios/ ESP2866 GPIO pins

https://github.com/esprfid/esp-rfid ESP RFID

https://www.youtube.com/watch?v=c0tMGlJVmkw Pin modes

https://tasmota.github.io/docs/Displays/ Tasmota Displays

DisplayModel 2
DisplayAddress 0x3C
DisplayDimmer 100
DisplayWidth 128
DisplayHeight 32


Displaymode

0 DisplayText DisplayText DisplayText
1 Time/Date Time/Date Time/Date
2 Local sensors Local sensors Local sensors
3 MQTT and Time/Date Local sensors and Time/Date Local sensors and Time/Date
4 Local sensors MQTT and local sensors MQTT and local sensors
5 MQTT and Time/Date MQTT, local sensors and Time/Date MQTT, local sensors and Time/Date

So, for UK, your configuration, to be typed on the console, should be:
TimeZone 99
TimeDST 0,0,3,1,1,60
TimeSTD 0,0,10,1,2,0


https://templates.blakadder.com/heltec_wifi_kit_8.html Heltec Wifi 8 Template

https://tasmota.github.io/docs/PIR-Motion-Sensors/ PIR Motion Snesors

https://oneguyoneblog.com/2019/10/01/tasmota-esp8266-nodemcu-arduino-ide/ Tasmota LEDs

https://randomnerdtutorials.com/esp8266-and-node-red-with-mqtt/ esp2866 node red mqtt

https://oneguyoneblog.com/2020/02/29/flashing-tasmota-on-sonoff-basic-r2-using-linux/ Flashing Tasmota from Linux

sudo apt-get install esptool
esptool --port /dev/ttyUSB0 flash_id
esptool --port /dev/ttyUSB0 read_flash 0x00000 0x100000 firmware1MB.bin
esptool --port /dev/ttyUSB0 erase_flash
For a version with 1MB flash memory:
esptool --port /dev/ttyUSB0 write_flash -fs 1MB -fm dout 0x0 tasmota.bin
For a version with 4MB flash memory:
esptool --port /dev/ttyUSB0 write_flash -fs 4MB -fm dout 0x0 tasmota.bin

D1 mini flash mode D3 --> GPIO0 ---> gnd

SwitchMode1 1
Rule1 on Switch1#state=1 do publish stat/thing4/PIR1 ON endon on Switch1#state=0 do Publish stat/thing4/PIR1 OFF endon
Rule1 1

https://tasmota.github.io/docs/Supported-Peripherals/ Tasmota Peripherals

https://notenoughtech.com/featured/sonoff-tasmota/ Not enough Tech Tasmota page

https://notenoughtech.com/raspberry-pi/flash-esp8266-nodemcu/ Flashing ESP8266 with NodeMCU (Windows, Linux, Arduino and Raspberry Pi)

https://drzzs.com/d1-mini-tasmotized-motion-detection-rgb-temp-humidity/ Dr Zs Tasmota D1 Mini Sensor page

http://tasui.shantur.com/ Find Tasmotas